C1 - Firmware - current version and changes.

[DorinDXN]

C1E_02391 is published

When pressing and hold [3] at -=-=-= after power up, for Wi-Fi reset, only these changes are made:
SSID of MECHA to MECHA-NNNNNN, where NNNNNN are made from the MECHA's ID
SSID password to 12345678
update password to 87654321
admin /config password set to Mecha
UI password set to none
Default mode set to AP
STA Mode values for IP set to no values (auto)
Trusted IP set to none
pairing pin set to none
if MECHA was part of DAC, the pairing procedure needs to be repeated to work in DAC again
Wi-Fi Power set to 100
MECHA will try to update the firmware via hot-spot M-NNNNNN using password 12345678 if that hot-spot is active, please activate it if MECHA fails to boot.

[DorinDXN]

C1E_02390 is published

The MSS Language in pitch and yaw conventions accepts now RT, RW and WO at the end of script
"RT" means Return to start position on the shortest path (like before)
"RW" means Rewind to start position without taking the shortest path, this is useful e.g. when cables to a power bank are used.
"WO" means Without Optimization.
If "WO" is used, MECHA will not optimize any move for the shortest path,
thus "RT", "RTWO", "RW", "RWWO", "WORW".. become valid as well.
Please test any pitch and yaw script with these new additions (without cables) before actual use to be sure is what you want.

[DorinDXN]

C1E_02387 is published

The pause until the repeat of the preset, when Repeat times*seconds is used,
can be now bypassed by pressing [>]
or the repeat can be canceled by pressing [power].

[DorinDXN]

C1E_02386 is published

Addressed an issue regarding [x] Less Noise for E rotator(s)
if enabled in /config, it caused wrong movements and slider jumps and/or disappear.

[DorinDXN]

MECHA FW bug alert!

Please disable the "LESS NOISE.."
if is enabled in /config for MECHA C1
[x] Less Noise for E rotator(s)

it is disabled by default, if you didn't enable it, no action is needed.

Working on a fix for the next FW update.

[DorinDXN]

C1E_02382 is published

Optimizations for C2 -> C1 preset compatibility

[DorinDXN]

C1E_02373 is published

Addressed an issue regarding the Slider wasn't initialized if "[x] Use cache for UI translation" was enabled in /config

[DorinDXN]

C1E_02372 is published

Addressed an issue regarding button [3] on NN IR Remote has shown the code IR 4 instead of IR 31 when executing the IR Test.

[DorinDXN]

C1E_02371 is published

Addressed an issue regarding up and down limits in partial panorama, when one of them was 0, MECHA ignored that limit.

The IR Remote test will automatically enable the use of the NN IR Remote if is not enabled, without need to access /config anymore.

[DorinDXN]

C1E_02370 is published

Addressed an issue regarding the Slider in collapsed form got stuck.

[DorinDXN]

C1E_02367 is published

Addressed an issue regarding the Slider reflected the end position wrong as Level instead of Raised or Parked, if the preset was started in Raised or Parked.

[DorinDXN]

C1E_02366 is published

Addressed an issue regarding the Slider in collapsed form failed to rotate the motors.

[DorinDXN]

C1E_02365 is published

Addressed an issue regarding the corners in slider in some cases when old rotators E1 were used.

[DorinDXN]

C1E_02364 is published

Optimized the design of the slider for better visibility and responsiveness.
In the combined button under the Slider, added [Corner 1] and [Corner 2] for SET the current position as corner or GO to corner.

[DorinDXN]

C1E_02363 is published

Added a "moving.." text to be shown when slider commands MECHA to move
The slider will use the current settings for speed, micro-stepping and profile for motor commands.
in RAW interface there added &sim parameter, if is passed in commands MECHA will not move the motors, instead only will simulate and return the values.
the &pr &sp and &ms can have number or not, without number they will specify all the rotators in MECHA
e.g. &ms1=32 will specify the micro-stepping for rotator 1 while &ms=32 will do for both rotators.