Announcement

Collapse
No announcement yet.

Firmware - current version and changes.

Collapse
This topic is closed.
X
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • C1E_02133 is published

    The code 31< for automatic shooting pattern computed by MECHA, without using the UI, works now for Single MECHA as well.
    After entering the 31< code, MECHA will flash the power button and waits for two quick presses of the power button,
    first is in order to trigger the camera and the second is after the camera was triggered.
    After that, MECHA will rotate slowly to the right and wait another press of power button right after the sheet of paper is out of the camera's frame.
    Then MECHA will go back in initial position and will start to flash 1, 2 and 3 LEDs
    and waits for one of the buttons [1] [2] or [3] to be pressed to assign the computed preset to that particular button.
    To cancel the assignment, the power button can be pressed instead.
    The assigned preset will work for Single MECHA and MECHA DAC as well.
    If Single MECHA is used, after first row MECHA will enter in pause and suggests, on LEDs, a manual tilt of the vertical axis to continue to full spherical panorama.
    If only cylindrical is needed or no manual tilt is possible, press the [power] button of MECHA.
    1. Mecha it possible.
    2. Mecha it easy.
    3. Mecha team up.

    4. ..

    Comment


    • C1E_02134 is published

      Added a simple way to program a preset
      e.g. 192.168.8.1/preset?b=1&s=12&f=30&p=2
      this will set on button 1 (b=1)
      a preset for cylindrical 12 shots around (s=12)
      or, optional
      full spherical panorama shoot with 30 mm (f=30) valid from 10 to 200
      and, optional
      a pause of 2 seconds after shoot (p=2)

      the page will ask for credentials:
      admin
      Mecha
      1. Mecha it possible.
      2. Mecha it easy.
      3. Mecha team up.

      4. ..

      Comment


      • C1E_02135 is published

        Addressed an issue regarding a partial panorama, e.g. (200),
        added to simple script, in MSS format, not worked properly and produced a full 360 deg. panorama instead.
        1. Mecha it possible.
        2. Mecha it easy.
        3. Mecha team up.

        4. ..

        Comment


        • C1E_02136 is published

          Addressed an issue regarding the programming of a preset using parameters,
          with the s= parameter given,
          produced 30 deg. interval instead of the required one
          when the preset was executed using the buttons and not from UI.
          1. Mecha it possible.
          2. Mecha it easy.
          3. Mecha team up.

          4. ..

          Comment


          • Please let me know if the buttons [1][2][3] of NN IR remote are not working after this update.

            C1E_02137 is published.


            The programming of a preset using parameters, can have h= and v= to specify the area in degrees of a partial panorama
            e.g. 192.168.8.1/preset?b=1&f=80&h=100&v=75
            partial panorama for 80 mm lens, 100 degrees wide and 75 degrees tall.

            Added support for future NN IR Remote, with better handling of a power OFF function
            More details will be published another time.
            1. Mecha it possible.
            2. Mecha it easy.
            3. Mecha team up.

            4. ..

            Comment


            • C1E_02138 is published

              Added 3231< code for testing the IR Remote
              After the code is entered, MECHA will not execute the commands given by buttons.
              Instead, it will only beep and display the code of the button pressed on LEDs (after the button is released) and over the battery symbol in UI.
              To end the test, press the [power] button of MECHA, which is flashing during the test.
              1. Mecha it possible.
              2. Mecha it easy.
              3. Mecha team up.

              4. ..

              Comment


              • C1E_02139 is published

                Added in config/ [x] Use Aux Pulse, if exists.
                If you use MECHA in applications requiring the Aux Pulse file, you need to thick this box from now on,
                default is clear and can be ignored.

                The Wake (W:) delay has now an enhanced behavior if is a negative value.
                e.g. W:-5 sec. will also force a before (B:) delay if is B: not zero.
                A small negative, under 1 second, value will trigger the Wake signal, which is a focus signal, before every position instead of only at the begin of a session. e.g. w:-0.9 sec. or W:-0.1 sec.
                There are no changes for positive W: values, regardless of their size.
                1. Mecha it possible.
                2. Mecha it easy.
                3. Mecha team up.

                4. ..

                Comment


                • C1E_02140 is published

                  Addressed an issue causing double press on IR power button of Remote didn't initiate the shut-down.
                  Optimizations in RAM management
                  1. Mecha it possible.
                  2. Mecha it easy.
                  3. Mecha team up.

                  4. ..

                  Comment


                  • C1E_02141 is published

                    Enhanced the possibilities when use the custom protocol on AUX port.
                    With common remotes, a half-press is detected as 1A, a full press is detected as 1A1S,
                    These are the possibilities now, e.g. for a half-press:
                    045=1A, execute the a preset which starts with 045+blank in name.
                    -045=1A, execute the a preset which starts with 045+blank in name but, in the opposite sense of rotation.
                    HS=1A, Home Set for the follow, also a Home Set can be done by pressing the power button.
                    45.0=1A, rotates with 45.0 degrees.
                    -45.0=1A, rotates with -45.0 degrees.
                    the above uses the inverse rotation for buttons, if is set.
                    H=1A, return to Home position set by HS or by the power button.
                    1. Mecha it possible.
                    2. Mecha it easy.
                    3. Mecha team up.

                    4. ..

                    Comment


                    • C1E_02142 is published

                      Some changes regarding the custom protocol on AUX port
                      45.0=1A, rotates at 45.0 degrees from Home position, absolute.
                      -45.0=1A, rotates at -45.0 degrees from Home position, absolute.
                      ^45.0=1A, rotates with 45.0 degrees from previous position, incremental.
                      ^-45.0=1A, rotates with -45.0 degrees from previous position, incremental.
                      1. Mecha it possible.
                      2. Mecha it easy.
                      3. Mecha team up.

                      4. ..

                      Comment

                      Working...
                      X